DIME DISTORTION
Power: Dunlop ECB-004 18-volt AC
Adapter
Controls: Footswitch
toggles effect on/hardwire bypass (red LED indicates on)
. Output knob sets total output level .
Gain knob controls amount of distortion
. 3-band EQ tailors overall tone . Scoop switch
notches
mids for Dime-approved metal tones
DUN-DD11
|
BLUE BOX
Power: Dunlop ECB-003 AC Adapter
or Single 9v battery
Controls:
Footswitch toggles effect on/bypass
(red LED indicates on) . Output knob sets total
effect output level . Blend knob adjusts ratio of
dry and effected signal
DUN-M103
|
WYLDE OVERDRIVE
Power: Dunlop ECB-003 AC Adapter
or Single 9v battery Controls: Footswitch
toggles effect on/hardwire bypass (red LED indicates on). Output knob
sets total output level . Gain knob controls amount of distortion Tone
knob tailors overall EQ
DUN-ZW44
|
DISTORTION+
Power: Dunlop
ECB-003 AC Adapter or Single 9-volt battery
Controls: Footswitch
toggles effect on/bypass (red LED indicates on). Output knob sets
total output level . Distortion knob controls amount of distortion
DUN-M104
|
TEN BAND EQUALIZER
Power: Dunlop
ECB-004 18-volt AC Adapter
Controls: Footswitch toggles
effect on/hardwire bypass (illuminated sliders indicates on)
Ten sliders enable boost or cut up to
12dB at 31.25Hz, 62.5Hz, 125Hz, 250Hz, 500Hz,
1kHz,
2kHz, 4kHz, 8kHz, 16kHz . Separate
Input Gain and Output Level sliders (+/- 12dB) . Dual outputs for
stereo applications.
|
PHASE 100
Power:
Dunlop ECB-003 AC Adapter or Single 9-volt battery
Controls:
Footswitch toggles effect on/bypass (red LED
indicates on)
. Intensity knob selects one of four preset phase
waveforms . Speed knob varies rate of phase sweep
DUN-M107
|
EVH PHASE 90
Power: Dunlop ECB-003 AC
Adapter or A 9-volt battery Controls: Footswitch toggles
effect on/bypass ( LED indicates on)
. Speed knob varies rate of phase sweep
. Script Button selects between smooth and lush
70’s
style e phasing and a modern edgier phase tone
|
10-BAND GRAPHIC EQUALIZER
Power: Dunlop
ECB-004 18-volt AC Adapter
Controls: Footswitch toggles
effect on/hardwire
bypass (illuminated sliders indicates on) .
Ten sliders enable boost or cut up to 12dB at 31.25Hz,
62.5Hz, 125Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz, 16kHz.
Separate Input Gain and Output Level sliders
(+/- 12dB)
DUN-M108
|
PHASE 90
Power: Dunlop
ECB-003 AC Adapter or A 9-volt battery Controls:
Footswitch toggles effect on/bypass (red LED
indicates
on). Speed knob varies rate of phase sweep
|
6-BAND GRAPHIC EQUALIZER
Power: Dunlop ECB-003 AC
Adapter or A 9-volt battery
Controls: Footswitch
toggles effect on/hardwire
bypass. Six sliders enable boost
or cut up to 18db at frequency centers 100Hz,
200Hz, 400Hz, 800Hz, 1.6kHz and 3.2kHz
DUN-M109
|
DYNA COMP
Power: Dunlop ECB-003 AC
Adapter or
Single 9-volt battery
Controls: Footswitch
toggles effect
on/bypass (red LED indicates on). Output
knob sets compressed output level . Sensitivity
knob sets compression level (highest sensitivity is maximum
compression)
|
FLANGER BY MXR
Power: Two 9v batteries or
Dunlop ECB-004 18v Adapter
Controls: Footswitch
toggles effect on/bypass (LED indicates on) . Manual knob selects
frequency center of effect when auto-sweep is
disengaged . Width knob at
zero disengages auto-sweep, rotates clockwise
to increase total phase sweep of effect . Speed
knob
modulates rate of effect Regen knob feeds effect back onto itself at
adjustable intensity, increasing the total phase effect .
EVH Switch activates preset Manual, Speed, Width,
and
Regeneration settings for instant “Unchained” tone
|
FLANGER
Power: Two 9-volt batteries or
Dunlop ECB-004 18-volt AC Adapter; Controls: Footswitch
toggles effect on/bypass (red LED indicates on).
Manual knob
selects frequency center of effect when auto-sweep
is
disengaged . Width knob at zero disengages
autosweep,
rotates clockwise to increase total phase sweep of
effect
. Speed knob modulates rate of effect Regen knob
feeds
effect back onto itself at adjustable intensity,
increasing
the
total phase effect. DUN-M117R
|
SMART GATE
Power: Single
9-volt battery or Dunlop ECB-003 AC Adapter
Controls: Footswitch toggles
effect on/hardwire bypass
(red LED indicates on) . Trigger Level knob allows
adjusting the threshold level of gate . 3-position
switch
selects type of noise reduction: Hiss, Mid Range,
or Full
. Gate LED shows level of noise reduction
|
AUTO Q
Power: Single 9-volt battery or
Dunlop ECB-003 AC Adapter Controls: Footswitch
toggles effect on/bypass (red LED indicates on). Range knob controls
frequency floor of effect The Q knob adjusts the intensity of the wah
effect . Volume controls overall effect output level (inactive in Bypass mode) . Decay
knob controls the drop-off of the wah effect (with Blend knob off) or
transition between wah and shimmer (with Blend dialed up) . Blend
knob controls the mix between auto-wah and shimmer
. Rate knob controls the speed of the shimmer
effect
.
Band switch selects frequency range of effect
|
DOUBLE-SHOT DISTORTION
Power: Dunlop ECB-004 18-volt AC
Adapter
Controls: Left
footswitch toggles effect on/hardwire
bypass (center red LED indicates on) . Right
footswitch toggles between the two channels (red
LED to
the right of channels indicates active channel)
Each channel features knobs for Bass, Mid, Treble,
Gain, and Output . Each channel features Focus
switch for tailoring low-end response
(yellow LED indicates on)
|
SUPER COMP
Power: Single
9-volt battery or Dunlop
ECB-003 AC Adapter Controls: Footswitch
toggles effect on/hardwire bypass . Output
knob sets compressed (attenuated) output
level . Attack Level knob sets the attack
attenuation level (highest attack level is minimum attack
attenuation). Sensitivity knob sets the compression ratio (highest
sensitivity is maximum compression)
|
MXR BASS BLOW TORCH
Power: Dunlop
ECB-004 18-volt AC Adapter or Two
9-volt batteries Controls:
Footswitch toggles effect
on/true hardwire bypass (blue LED indicates on) .
Volume
knob sets the overall output level .
Bass/Midrange/Treble knobs control the EQ of the
distorted signal . Mid Shift switch selects between 250Hz, 750Hz, or
2KHz . Blend knob adjusts the mix between distorted and clean
signals . Gain knob controls
the amount of distortion . Side-mounted Torch
switch adds +12dB of EQ tailored distortion gain
|
MICRO AMP
Power: Single 9-volt battery or
Dunlop
ECB-003 AC Adapter Controls:
Footswitch toggles effect on/bypass
(red LED indicates on). Gain knob
adjusts total output volume when Micro Amp is
engaged
|
BASS AUTO Q
Power: Single 9-volt battery or
Dunlop ECB-003 AC
Adapter Controls: Footswitch
toggles effect
on/bypass (red LED indicates on) . Range knob
controls
frequency floor of effect . The Q knob adjusts the
intensity of the wah effect . Volume controls overall effect output
level (inactive in Bypass mode) . Decay knob
controls the drop-off of the wah effect
(with Blend knob off) or transition between wah
and shimmer (with Blend dialed up). Blend knob controls the mix
between auto-wah and shimmer. Rate knob controls the speed of the
shimmer effect
|
STEREO CHORUS
Power: Two
9-volt batteries or Dunlop
ECB-004 18-volt AC Adapter Controls:
Footswitch toggles effect on/hardwire bypass
(red LED indicates on). Intensity control adjusts overall effect
level . Rate and Width knobs tailor chorus tone, from subtle and
sparkly to lush and watery. Bass and Treble knobs EQ the modulated
frequencies only. Stereo outputs for a huge tonal spread .Bass Filter
button leaves low end intact
|
BASS D.I.+
Power: Single 9-volt battery or
Dunlop ECB-003 AC
Adapter Controls: Effect
footswitch toggles effects
on/bypass . Distortion footswitch toggles
Distortion
channel in/out . Bass/Mid/Treble EQ knobs . Color
switch activates pre-set EQ optimized for bass.
Clean
Volume knob adjusts output level of Clean channel.
The following knobs are only active when Distortion channel is
selected: . Blend knob controls the mix
between distorted/clean signal . Gate Trigger knob sets the
sensitivity of the Noise Gate . Gate switch selects Noise
Gate in/out . Gain knob sets distortion level . Phantom/Ground
switch selects between Direct Output Ground Lift (switch up) and
Phantom
Power (switch depressed)
|
